ATUS-Axial Piston Variable Pumps-APV-PAVC-500×1000

APV-PAVC-33

APV-PAVC Series Axial Piston Variable Pumps
Size NG
33
Displacement
33 cm³/rev
Speed
1800 rpm
Flow
59.4 L/min
Nominal pressure
207 bar
Max. Pressure
248 bar
Weight (approx.)
18 kg

Products and performance

The APV-PAVC-33 variable-displacement axial piston pump features an NG33 mounting interface, a displacement of 33 cm³/rev, and a rated speed of 1800 rpm, delivering a stable flow rate of up to 59.4 L/min. With a rated pressure of 207 bar and a peak pressure capacity of 248 bar, it is exceptionally well-suited for high-load and heavy-duty operating conditions.
Designed for high reliability and versatility, this pump maintains consistent performance even in demanding industrial environments. It is widely used across various sectors, including injection molding machines, construction machinery, metallurgy, plastics processing equipment, and the paper industry. Combining high energy efficiency, superior performance, and long-term operational reliability, the APV-PAVC-33 serves as an ideal core power component for high-pressure, heavy-duty industrial hydraulic systems.
ConeMac-Axial Piston Fixed Pump-APF-A2FO Series-Video

Energy‑Saving Performance

Variable displacement from 0 to 33 cm³/rev matches pump output to real demand, cutting energy consumption and hydraulic oil waste during continuous industrial operation.

High Working Efficiency

Delivering a stable 59.4 L/min output with low internal leakage, the pump keeps the entire hydraulic system working at high overall efficiency under varying loads.

Precise Control

At a rated 1800 rpm, the variable mechanism enables accurate flow regulation and repeatable actuator speed, keeping operation smooth and stable across the full working range.

High Adaptability

Designed for injection molding, construction machinery, metallurgy, plastics and papermaking industries, this pump delivers steady performance under varied operating conditions.

Outstanding Reliability

A compact 18 kg build with 207 bar nominal and 248 bar peak pressure ratings delivers dependable, long-hour hydraulic power for continuous heavy-duty industrial duty.

Specifications

APV-PAVC-33 General Information

The APV-PAVC-33 variable piston pump in NG 33 size fits compact hydraulic power units where space and efficiency both matter.
A 33 cm³/rev displacement gives this pump a balanced flow reserve for mid-size industrial circuits.
Rated 1800 rpm, it pairs cleanly with standard four-pole motors for quiet, efficient drive.
59.4 L/min of continuous flow keeps injection molding and plastic machinery running without interruption.
207 bar nominal pressure covers typical working loads in general industrial hydraulics.
Short pressure peaks up to 248 bar are absorbed without tripping relief settings.
At approximately 18 kg, the unit mounts quickly and adds little load to machine frames.
Typical uses include injection molding machines, engineering machinery, metallurgy, plastic machinery and papermaking.

Product Features of APV-PAVC Series Variable‑Displacement Axial Piston Pumps

Energy‑saving Operation:Automatic displacement adjustment reduces energy and hydraulic oil waste.
High Hydraulic Efficiency:Optimized power output improves overall system working efficiency.
Precise Control:Advanced variable‑displacement technology realizes accurate hydraulic control.
Improved Equipment Stability:Enhances running accuracy and stability of matched machinery.
Strong Adaptability:Sustains stable performance under diverse harsh working conditions.
High Operational Reliability:Delivers consistent and dependable hydraulic power output.
Stable System Performance:Displacement adjustment guarantees steady hydraulic system status.
Excellent Comprehensive Performance:Balances efficiency, control and durability for heavy‑duty use.
- The factory assembly clearance between piston ball head and slipper ball socket is normally 0.015~0.025 mm.
- After prolonged service, the clearance enlarges. Parts can still be used if the clearance does not exceed 0.3 mm.
- Overlarge clearance will cause increased pulsation of pump outlet pressure and flow.
- In serious cases, loose slippers and slipper detachment may happen, further resulting in severe pump damage.
- Once signs of pressure and flow pulsation are detected, inspect slipper looseness in advance and conduct slipper re-clinching promptly.
- After long-term operation, concave deformation will form on the flat surface of the swash plate.
- The workpiece can be surface-ground followed by nitriding treatment.
- If the removed material thickness (e.g. 0.2 mm) does not completely eliminate the original nitrided layer, re-nitriding may be omitted.
- Hardness inspection of the swash plate surface is mandatory in such cases.
- Excessive bearing internal clearance will break the normal clearance of friction pairs and damage the oil film thickness of hydrostatic support, shortening the service life of piston pumps.
- The average service life of general bearings reaches 1000 hours (roughly more than two years). Bearings shall be replaced as appropriate after exceeding this service period.
- Replace with bearings of the identical model marked on the removed old bearing, or verified interchangeable alternatives.
- If grooves are scratched on the swash plate surface by piston ball heads (applicable to radial piston pumps), laser cladding with alloy powder is recommended for repair.
- Laser cladding ensures high bonding strength and hardness of deposited material without reducing the hardness of surrounding base metal.
- Manual overlay welding with chromium-type welding electrodes is an alternative method. The repaired swash plate surface requires re-heat treatment, preferably in a nitriding furnace.
- Regardless of the repair method adopted, the original dimensional accuracy, hardness and surface roughness of the swash plate must be restored.
Low oil Level Inclination Angle-Front Up
45 °
Low oil Level Inclination Angle-Back Up
45 °
Low oil Level Inclination Angle-Fuel Pump Side Up
45 °
Low oil Level Inclination Angle-Exhaust Side Up
45 °
Oil Sump Capacity-Upper Limit
14.2 L
Oil Sump Capacity-Lower Limit
12.4 L
Capacity of The Whole System
16.4 L
Main Causes and Troubleshooting Methods for Hydraulic Pump No Oil Suction / No Oil Discharge
  • Damage to the hydraulic pump, pump motor, or coupling between motor and pump. Replace the faulty pump, motor or coupling in a timely manner.
  • Too low oil level in the tank or excessively high pump installation position causes suction failure. Refill oil to the gauge level or adjust the pump height to keep the suction lift within the specified range.
  • Oil impurities and increased viscosity block the suction filter and oil pipe. Clean pipes and filters regularly and replace with qualified hydraulic oil as required.
  • Oil impurities and increased viscosity block the suction filter and oil pipe. Clean pipes and filters regularly and replace with qualified hydraulic oil as required.
Main causes and troubleshooting methods for hydraulic pumps discharging oil but lacking pressure and exhibiting reduced efficiency.
  • Severe wear of internal sliding parts leads to low volumetric efficiency and excessive axial/radial clearance. Replace the hydraulic pump or perform complete overhaul.
  • Damaged oil pipes and poor suction-side sealing cause air intake. Check all connections, reseal joints or replace damaged pipelines.
  • Blocked oil pipes and heavily contaminated filters. Clean pipelines and filters thoroughly to ensure full flow cleanliness.
  • Incorrect variable pump adjustment and severely worn relief valve spool. Readjust flow parameters and replace worn relief valve components for stable pump operation.
  • Motor speed below rated value and internal foreign impurities. Match the correct motor per specifications and clean internal impurities timely.
Major Causes of Excessive Noise During Hydraulic Pump Operation and Methods for Troubleshooting
  • Mostly caused by clogged filter, low oil level, air inhalation via oil seal and pipelines. Check tank oil level, repair pipelines, inspect pump seals, clean pipes and filters, and replace hydraulic oil periodically.
  • Excessively high oil viscosity, low oil temperature and entrained air bubbles. Select suitable hydraulic oil according to seasons.
  • Damaged coupling or misalignment between pump and motor leads to heavy vibration and loud noise. Inspect coupling wear, replace coupling and complete alignment strictly as installation requirements.
  • Operating speed exceeds rated value and mismatched driving motor. Reduce pump speed and select a suitable motor.
  • Worn shaft seal causes air intake; loose pump end cover bolts. Replace pump shaft seal and tighten cover bolts.
  • Low gear precision, poor contact or damaged internal parts of gear pump. Replace or grind gears, renew damaged components.
  • Insufficient axial clearance, out-of-tolerance perpendicularity or parallelism. Replace the gear pump entirely.
  • Blockage inside relief valve. Clean or replace the relief valve.
  • Vibration generated by unfixed pipelines. Secure all hydraulic pipelines firmly.
Main Causes of Oil Leakage from Hydraulic Pump Bodies and Methods for Rectification
  • Failure of the piston pump central spring breaks sealing between cylinder block and valve plate. Replace the spring and re-seal the mating surface.
  • Damaged oil seals or worn/poorly fitted gaskets at pipeline connections. Replace all defective sealing parts.
  • Severe wear of internal pump parts resulting in oversized operating clearances. Replace or refit the relevant components.
Main Causes of Hydraulic Pump Overheating and Troubleshooting Methods
  • Excessively high or low oil viscosity, and accumulated impurities after long service. Replace hydraulic oil in a timely manner and adopt oil with proper viscosity.
  • Heavy wear between pump side plates, shaft sleeves and gear end faces leads to overheating. Replace side plates, shaft sleeves or install a new hydraulic pump.
  • Small tank volume restricts heat dissipation and triggers high oil temperature. Increase tank capacity and expand heat dissipation area.
Installation Drawing
Download
Installation Manual
Download
Operation Manual
Download
Parts Catalogue
Download
Report & Certifcate
Download

Other Models

100 cm³/rev
Speed
1800 rpm
Flow
180 L/min
Weight (approx.)
50 kg
Nominal pressure
207 bar
65 cm³/rev
Speed
1800 rpm
Flow
117 L/min
Weight (approx.)
28 kg
Nominal pressure
207 bar
38 cm³/rev
Speed
1800 rpm
Flow
68.4 L/min
Weight (approx.)
18 kg
Nominal pressure
207 bar
33 cm³/rev
Speed
1800 rpm
Flow
59.4 L/min
Weight (approx.)
18 kg
Nominal pressure
207 bar
CCEC-Engine
CCEC-Engine
find more

Cummins China Engine

Cummins have 6 50:50 joint venture engine plants in China partnershipped with different Chinese automotive or equipment manufacturers, including DCEC-Dongfeng Cummins, CCEC-Chongqing Cummins, BFCEC-Beijing Foton Cummins, XCEC-Xi’an Cummins, GCIC-Guangxi Cummins, APCL-Anhui Cummins. EMAC Power is working with all of these engine plants, providing customers full ranges of customize engine power pack with all of Cummins engines produced in China.
find more

Fast Gear

The F6A Series Automated Transmission uses the FAST automatic transmission, has six front gears, the transmission ratio step arrangement is reasonable, has very outstanding fuel economy. Adopt hydraulic automatic transmission. The F6A Series Automated Transmission has six gears, each with a different reduction ratio.
ev-truck
ev-truck
find more

EV Truck

Electric wheel dump trucks use electricity as a power source, completely abandoning traditional fuel engines. This change enables the vehicle to achieve true “zero emissions” during operation, without the emission of pollutants such as carbon monoxide, nitrogen oxides, and particulate matter in the exhaust gas, greatly reducing the pollution to the atmospheric environment.
find more

DANA Axle

Applying the advanced technology of DANA with high efficiency, fuel economy, strong load torque, low noise,high reliability, lower procurement cost, low repair cost and lower maintenance cost.
find more

Datong Gear

The Datong HW25712XSJ Heavy Manual No-Sync Gearbox has a torque of 2500 N.m, a gear ratio range of 14.941-1, an oil capacity of 13 L (13.5 L when equipped with a power take-off), an overall length of 993 mm, and a weight of 428 kg.
DFZ5258JSQSZ6D
find more

Crane Trucks

The DFZ5258JSQSZ6D truck crane is a powerful and versatile vehicle designed for efficient lifting and transportation tasks. Equipped with a YCS06300-61 engine and a Shaanxi Auto Fast gear : 10JS120TA high-low gear with synchronizer、PTO gearbox, it provides strong and stable power for demanding operations.

FREQUENTLY ASKED QUESTIONS

Get quick answers about this engine

With full ranges of emission standard from Euro 2 to Euro 7, Dongfeng Cummins producing 12 series automotive engines, started from 3.9 liter engine, to 15 liter engine, covering the power range of 125HP to 650HP.
Dongfeng Cummins automotive engine customize developing configurations for big vehicle OEMs in China, based on each of requirement, Dongfeng Cummins producing dozens of different configuration engines with same engine model number, which only SO-Shop Order will be different with each other, the SO number is the identify number of the engine configuration of each model.
Even with same engine model, different SO number engine can have very different configuration with each other, with different prices. Some of SO-Shop Order is not available for commercial market, such as restricted models (Usually for military specifications).
EMAC offering most common, cost effective models which also able to process the production in Dongfeng Cummins, which usually have following accessories as standard configuration.

Power OutPut
180 HP(132kW)
Max Torque
610 Nm
Displacement
5.9L
6 Inline
5.9L
Fuel System
Bosch Mechancial Pump
Emission Standard
Euro II

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry’s

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry’s

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry’s

Contact Us Now !!!

We are ready to provide professional support

Sales Director

Mr.Jasper Lee
Chat On whatsApp

Sales Manager

Mrs.Wendy Fu
Chat On whatsApp

Spare Parts Sales

Miss. Nora Cao
Chat On whatsApp

After-sales Manager

Miss. Tina Zhang
Chat On whatsApp

Merchandiser

Miss. Miss
Chat On whatsApp
SEND US A MESSAGE

Google reCaptcha: Invalid site key.

CONTACT INFORMATION
Traveling Guidence

phone

Tel: +86-755-8231-4520

Hours

Monday-Friday: 9am – 7pm | Saturday-Sunday: Closed

Headquarters

23RD FLOOR, LINSN TOWER, GUANGMING, SHENZHEN, CHINA. 518107

FIND US
Headquarters
23RD FLOOR, LINSN TOWER, GUANGMING, SHENZHEN, CHINA. 518107
Input error
cancel